Rinker Boat Graphic Decal | 2002 Captiva 192 212 232 Gray Blue Set - All Questions
Rinker Boat Graphic Decal | 2002 Captiva 192 212 232 Gray Blue Set
SKU
1051302
How do I install this decal on my boat?
Question by: Ricky Watts on May 18, 2021, 1:35 PM
Hi Ricky,
The proper way to install this decal would be to clean the hull with an acid base cleaner to remove any grime and wax residue. From there, let the surface dry completely for 24 hours. Next you will want to wipe the area with a clean microfiber cloth in order to remove any last dust particles. You will want to hold the decal up in place and use a light masking tape to secure it in order to check the potential location. Start peeling the backing paper at one end, and slowly start to apply. When completely installed, use a soft plastic squeegee to get rid of all the air bubbles. When the transfer paper is removed, and you see remaining air bubbles, try working them out with your fingers. If they will not come out, use a sharp razor blade to poke a very small hole in order to release the air. Let the adhesive settle for another 24 hours. You are then good to go! Thanks!
Jake
The proper way to install this decal would be to clean the hull with an acid base cleaner to remove any grime and wax residue. From there, let the surface dry completely for 24 hours. Next you will want to wipe the area with a clean microfiber cloth in order to remove any last dust particles. You will want to hold the decal up in place and use a light masking tape to secure it in order to check the potential location. Start peeling the backing paper at one end, and slowly start to apply. When completely installed, use a soft plastic squeegee to get rid of all the air bubbles. When the transfer paper is removed, and you see remaining air bubbles, try working them out with your fingers. If they will not come out, use a sharp razor blade to poke a very small hole in order to release the air. Let the adhesive settle for another 24 hours. You are then good to go! Thanks!
Jake
Answer by: Jake Doro on May 18, 2021, 1:36 PM
I have a 2002 rinker and this is the decal design that matches the one currently on it with the exception that it is on a blue and white boat and the blue in this decal is yellow. I noticed you had the color scheme but it is only for a 282 and not a 232. Thought I may have missed a 232 race flag with yellow on the site so thought I would send in a question just in case. Thanks
Question by: K on Jul 2, 2021, 4:03 PM
Hello!
Unfortunately we don't currently have that Captiva 232 graphic with yellow in it, and it isn't something we can source or order. We aren't aware of any retailers who might have "on the shelf" anymore. I'm afraid you may need to look into custom.
Sorry we could not help.
Gene
Unfortunately we don't currently have that Captiva 232 graphic with yellow in it, and it isn't something we can source or order. We aren't aware of any retailers who might have "on the shelf" anymore. I'm afraid you may need to look into custom.
Sorry we could not help.
Gene
Answer by: Gene Warmuth on Jul 3, 2021, 2:17 PM
What additional adhesive are you talking about above. I will need some obviously. Do these not already have adhesive on one side?
Question by: Mike Hembree on Apr 21, 2022, 8:32 AM
Hi Mike,
There is adhesive on the back, but it is partially dried out from storage at Rinker. A simple waterproof contact cement will work perfectly, or even a 3M spray adhesive can work, but it gets a bit sloppy.
Gene
There is adhesive on the back, but it is partially dried out from storage at Rinker. A simple waterproof contact cement will work perfectly, or even a 3M spray adhesive can work, but it gets a bit sloppy.
Gene
Answer by: Admin on Apr 21, 2022, 11:29 AM
WHAT TYPE OF ADHESIVE IS REQUIRED FOR DECAL PART #1051302?
Question by: GARETH AUBREY TABOR on May 11, 2023, 10:44 AM
Hello Gareth,
A simple waterproof contact cement works well.
Gene
A simple waterproof contact cement works well.
Gene
Answer by: Admin on May 11, 2023, 10:49 AM