Nitro Boat Raised Decal 136395 | 9 x 1 1/8 Inch Black Pewter Red - All Questions
Nitro Boat Raised Decal 136395 | 9 x 1 1/8 Inch Black Pewter Red
SKU
8102852
Are these the right decals for nitro boat seats
Question by: Rebecca on Jul 26, 2020, 12:11 PM
Hi Rebecca,
Certainly some potential! They have been used on some models in the past. If you have any further questions, feel free to contact back.
-
Jake
Certainly some potential! They have been used on some models in the past. If you have any further questions, feel free to contact back.
-
Jake
Answer by: Jake Doro on Jul 27, 2020, 10:31 AM
How do I install this decal on my boat?
Question by: Ricky Watts on May 18, 2021, 1:35 PM
Hi Ricky,
The proper way to install this decal would be to clean the hull with an acid base cleaner to remove any grime and wax residue. From there, let the surface dry completely for 24 hours. Next you will want to wipe the area with a clean microfiber cloth in order to remove any last dust particles. You will want to hold the decal up in place and use a light masking tape to secure it in order to check the potential location. Start peeling the backing paper at one end, and slowly start to apply. When completely installed, use a soft plastic squeegee to get rid of all the air bubbles. When the transfer paper is removed, and you see remaining air bubbles, try working them out with your fingers. If they will not come out, use a sharp razor blade to poke a very small hole in order to release the air. Let the adhesive settle for another 24 hours. You are then good to go! Thanks!
Jake
The proper way to install this decal would be to clean the hull with an acid base cleaner to remove any grime and wax residue. From there, let the surface dry completely for 24 hours. Next you will want to wipe the area with a clean microfiber cloth in order to remove any last dust particles. You will want to hold the decal up in place and use a light masking tape to secure it in order to check the potential location. Start peeling the backing paper at one end, and slowly start to apply. When completely installed, use a soft plastic squeegee to get rid of all the air bubbles. When the transfer paper is removed, and you see remaining air bubbles, try working them out with your fingers. If they will not come out, use a sharp razor blade to poke a very small hole in order to release the air. Let the adhesive settle for another 24 hours. You are then good to go! Thanks!
Jake
Answer by: Jake Doro on May 18, 2021, 1:36 PM
can i order just the N please
Question by: Ed Vandeneng on Feb 23, 2022, 4:39 PM
Hello Ed,
I'm sorry, but we do not have the "N" by itself, and cannot split away from a complete decal. Not sure if a Nitro dealer would have single letters, but you could maybe try one.
Gene
I'm sorry, but we do not have the "N" by itself, and cannot split away from a complete decal. Not sure if a Nitro dealer would have single letters, but you could maybe try one.
Gene
Answer by: Admin on Feb 24, 2022, 8:58 AM
I have a 2007 Nitro 482 and I lost a couple of letters in my NITRO Decal on the boat..
The letters are raised trimmed in Gold as the one in the picture, but I'm not sure of the size.
Can u please help me with decal order?
The letters are raised trimmed in Gold as the one in the picture, but I'm not sure of the size.
Can u please help me with decal order?
Question by: Rev Herbert Davis on Jun 29, 2022, 8:23 PM
Hello Reverend,
Unfortunately, we aren't dealers, and have no way to cross reference the Nitro decals we have to specific boats. These letters are under 2" wide - does that seem close?
Gene
Unfortunately, we aren't dealers, and have no way to cross reference the Nitro decals we have to specific boats. These letters are under 2" wide - does that seem close?
Gene
Answer by: Admin on Jun 30, 2022, 10:32 AM