Triton 1896842 31 Inch Red / White / Black Boat Decals Pair - All Questions
Triton 1896842 31 Inch Red / White / Black Boat Decals Pair
SKU
1026430
How do I install this decal on my boat?
Question by: Ricky Watts on May 18, 2021, 1:35 PM
Hi Ricky,
The proper way to install this decal would be to clean the hull with an acid base cleaner to remove any grime and wax residue. From there, let the surface dry completely for 24 hours. Next you will want to wipe the area with a clean microfiber cloth in order to remove any last dust particles. You will want to hold the decal up in place and use a light masking tape to secure it in order to check the potential location. Start peeling the backing paper at one end, and slowly start to apply. When completely installed, use a soft plastic squeegee to get rid of all the air bubbles. When the transfer paper is removed, and you see remaining air bubbles, try working them out with your fingers. If they will not come out, use a sharp razor blade to poke a very small hole in order to release the air. Let the adhesive settle for another 24 hours. You are then good to go! Thanks!
Jake
The proper way to install this decal would be to clean the hull with an acid base cleaner to remove any grime and wax residue. From there, let the surface dry completely for 24 hours. Next you will want to wipe the area with a clean microfiber cloth in order to remove any last dust particles. You will want to hold the decal up in place and use a light masking tape to secure it in order to check the potential location. Start peeling the backing paper at one end, and slowly start to apply. When completely installed, use a soft plastic squeegee to get rid of all the air bubbles. When the transfer paper is removed, and you see remaining air bubbles, try working them out with your fingers. If they will not come out, use a sharp razor blade to poke a very small hole in order to release the air. Let the adhesive settle for another 24 hours. You are then good to go! Thanks!
Jake
Answer by: Jake Doro on May 18, 2021, 1:36 PM
Will these work on leather seat back and leather on front of console?
Question by: Jackie Switzer on Jul 25, 2022, 5:18 PM
Hi Jackie,
We sure don't know why they wouldn't. You may need to roughen the surface though.
Gene
We sure don't know why they wouldn't. You may need to roughen the surface though.
Gene
Answer by: Admin on Jul 26, 2022, 11:23 AM
Do these decals come with install instructions ? or could you send ?
Question by: Joe R Baker on Aug 31, 2022, 12:42 PM
Hi Joe,
There aren't any manufacturer instructions with them, but we do send this generic message with them:
Surfaces must be thoroughly cleaned before applying graphics or pinstripe.
Instructions:
Fiberglass Hulls:
Remove any dried matter (tape or glue) with a single edge razor blade. Thoroughly wipe surface clean with hot soapy water. This may take a number of passes depending on the surface condition. Rinse with clear warm water. DO NOT USE ANY ALCOHOL BASED PRODUCTS. Allow to dry for 72 hours in 50-90 degree heat. Wipe with lint free cloth.
Aluminum or Metal:
Remove any dried matter (tape or glue) with a single edge razor blade. Surface can be cleaned with a solvent such as Xylol or Lacquer thinner. Allow to dry for 72 hours in 50-90 degree heat. Wipe with lint free cloth.
There are a number of ways to apply decals and pinstripe. It comes down to personal preference. We highly recommend searching the web (youtube has several videos) for decal application. We also HIGHLY recommend cutting a 6" section off the pinstripe to test before applying the whole roll.
Hope this helps.
Gene
There aren't any manufacturer instructions with them, but we do send this generic message with them:
Surfaces must be thoroughly cleaned before applying graphics or pinstripe.
Instructions:
Fiberglass Hulls:
Remove any dried matter (tape or glue) with a single edge razor blade. Thoroughly wipe surface clean with hot soapy water. This may take a number of passes depending on the surface condition. Rinse with clear warm water. DO NOT USE ANY ALCOHOL BASED PRODUCTS. Allow to dry for 72 hours in 50-90 degree heat. Wipe with lint free cloth.
Aluminum or Metal:
Remove any dried matter (tape or glue) with a single edge razor blade. Surface can be cleaned with a solvent such as Xylol or Lacquer thinner. Allow to dry for 72 hours in 50-90 degree heat. Wipe with lint free cloth.
There are a number of ways to apply decals and pinstripe. It comes down to personal preference. We highly recommend searching the web (youtube has several videos) for decal application. We also HIGHLY recommend cutting a 6" section off the pinstripe to test before applying the whole roll.
Hope this helps.
Gene
Answer by: Admin on Aug 31, 2022, 1:05 PM